What failures may occur during the use of semi-enclosed hook sets? How to check?
The semi-enclosed hook set is a commonly used hook set accessory. This equipment can be used with lifting equipment for lifting operations, moving materials and heavy machinery equipment in the air, and is widely used in large-scale processing sites such as metallurgy and mining. Because its structure is relatively complex, once a failure occurs, it will directly affect the safety of the construction site. Therefore, we need to understand the possible failures of the semi-enclosed hook set and the inspection directions:
1. The hook appears to be inflexible in rotation
The reason for this situation is to consider whether the gap in the rotating part is too small, and whether the holes for installing the beam shaft and the pulley shaft on both sides of the plate are not parallel, causing the hook to be unable to deflect normally.
2. The hook cannot rotate continuously
This situation is mostly caused by not paying attention to the gap between the cross beams during the installation of the hook structure, resulting in a vertical deflection angle.
3. The hook cannot be lifted normally
In this case, it is necessary to check whether it is caused by damaged bearings or stuck wire ropes. If not, then the bearing may be failing due to increased rotational frictional resistance.
In summary, the above is an analysis of the possible causes of failure of the semi-closed hook group. Therefore, the editor here also calls on everyone to do a good job in daily lubrication of hooks and other lifting accessories to prevent the above failures from occurring frequently and reducing production efficiency.
The semi-enclosed hook set is a commonly used hook set accessory. This equipment can be used with lifting equipment for lifting operations, moving materials and heavy machinery equipment in the air, and is widely used in large-scale processing sites such as metallurgy and mining. Because its structure is relatively complex, once a failure occurs, it will directly affect the safety of the construction site. Therefore, we need to understand the possible failures of the semi-enclosed hook set and the inspection directions:
1. The hook appears to be inflexible in rotation
The reason for this situation is to consider whether the gap in the rotating part is too small, and whether the holes for installing the beam shaft and the pulley shaft on both sides of the plate are not parallel, causing the hook to be unable to deflect normally.
2. The hook cannot rotate continuously
This situation is mostly caused by not paying attention to the gap between the cross beams during the installation of the hook structure, resulting in a vertical deflection angle.
3. The hook cannot be lifted normally
In this case, it is necessary to check whether it is caused by damaged bearings or stuck wire ropes. If not, then the bearing may be failing due to increased rotational frictional resistance.
In summary, the above is an analysis of the possible causes of failure of the semi-closed hook group. Therefore, the editor here also calls on everyone to do a good job in daily lubrication of hooks and other lifting accessories to prevent the above failures from occurring frequently and reducing production efficiency.
The semi-enclosed hook set is a commonly used hook set accessory. This equipment can be used with lifting equipment for lifting operations, moving materials and heavy machinery equipment in the air, and is widely used in large-scale processing sites such as metallurgy and mining. Because its structure is relatively complex, once a failure occurs, it will directly affect the safety of the construction site. Therefore, we need to understand the possible failures of the semi-enclosed hook set and the inspection directions:
1. The hook appears to be inflexible in rotation
The reason for this situation is to consider whether the gap in the rotating part is too small, and whether the holes for installing the beam shaft and the pulley shaft on both sides of the plate are not parallel, causing the hook to be unable to deflect normally.
2. The hook cannot rotate continuously
This situation is mostly caused by not paying attention to the gap between the cross beams during the installation of the hook structure, resulting in a vertical deflection angle.
3. The hook cannot be lifted normally
In this case, it is necessary to check whether it is caused by damaged bearings or stuck wire ropes. If not, then the bearing may be failing due to increased rotational frictional resistance.
In summary, the above is an analysis of the possible causes of failure of the semi-closed hook group. Therefore, the editor here also calls on everyone to do a good job in daily lubrication of hooks and other lifting accessories to prevent the above failures from occurring frequently and reducing production efficiency.
Inquiry
Please leave us your requirements, we will contact you soon.