News

　　hook group's connection method with the wire rope winding system in the lifting mechanism depends on the number of branches carried by the lifting wire rope. When the lifting wire rope load index is 1, it can be directly connected to the end of the wire rope. Sometimes, in order to ensure that the hook has enough weight, the wire rope under no load will be tightened, so as to prevent the wire rope from bracketing on the pulley or drum due to looseness, and to achieve a smooth drop in the pressure control, an additional weight is often installed at the end of the rope to ensure that the hook has enough weight. The wire rope is tightened to prevent the wire rope from being bracketed on the pulley or drum due to looseness, and when the pressure-controlled drop is achieved, an additional weight is usually installed at the end of the rope, and the hook is hung on the wire rope with a number of support 2. The connection between the hook and the hook is the connection between the hook and the hook, which is the connection between the wire rope winding system between the hook and the lifting mechanism, as well as the hook hanging hook and the hook on the hook, and an additional weight is installed at the end of the rope to ensure that the hook has enough weight to tighten the wire rope under no load.

　　Hook is a combination of hooks and moving pulleys. It adopts a simple pick-up device, flexible rotation and simple use. Hooks are divided into two types: long and short. The long hook group adopts short hooks, with its pulley shaft on top, hook balance beam on bottom, and installed in parallel on the pull-up plate. It can have a number of single and double moving pulleys, the hook is short and the force is good. The length of the roll used is reduced accordingly. The pulley shaft of the short hook group is also a hook balance beam, which can eliminate pulling plates, but the number of pulleys must be symmetrical on both sides, so the pulley shaft is longer, the stress is poor, and the shaft is thick. When rotating the hook, use long grooves to avoid touching the pulley. However, the overall height of the hook group is small, so the short hook group is suitable for cranes with smaller lifting weight.

　　The above is some introduction to the applicable scenarios of hook groups shared by our semi-enclosed hook group manufacturers and everyone. You can learn about it. If you have any questions and needs, you can consult and contact us at any time! You can also leave your contact information directly on the website, and we will contact you in time!

　　hook group's connection method with the wire rope winding system in the lifting mechanism depends on the number of branches carried by the lifting wire rope. When the lifting wire rope load index is 1, it can be directly connected to the end of the wire rope. Sometimes, in order to ensure that the hook has enough weight, the wire rope under no load will be tightened, so as to prevent the wire rope from bracketing on the pulley or drum due to looseness, and to achieve a smooth drop in the pressure control, an additional weight is often installed at the end of the rope to ensure that the hook has enough weight. The wire rope is tightened to prevent the wire rope from being bracketed on the pulley or drum due to looseness, and when the pressure-controlled drop is achieved, an additional weight is usually installed at the end of the rope, and the hook is hung on the wire rope with a number of support 2. The connection between the hook and the hook is the connection between the hook and the hook, which is the connection between the wire rope winding system between the hook and the lifting mechanism, as well as the hook hanging hook and the hook on the hook, and an additional weight is installed at the end of the rope to ensure that the hook has enough weight to tighten the wire rope under no load.

　　Hook is a combination of hooks and moving pulleys. It adopts a simple pick-up device, flexible rotation and simple use. Hooks are divided into two types: long and short. The long hook group adopts short hooks, with its pulley shaft on top, hook balance beam on bottom, and installed in parallel on the pull-up plate. It can have a number of single and double moving pulleys, the hook is short and the force is good. The length of the roll used is reduced accordingly. The pulley shaft of the short hook group is also a hook balance beam, which can eliminate pulling plates, but the number of pulleys must be symmetrical on both sides, so the pulley shaft is longer, the stress is poor, and the shaft is thick. When rotating the hook, use long grooves to avoid touching the pulley. However, the overall height of the hook group is small, so the short hook group is suitable for cranes with smaller lifting weight.

　　The above is some introduction to the applicable scenarios of hook groups shared by our semi-enclosed hook group manufacturers and everyone. You can learn about it. If you have any questions and needs, you can consult and contact us at any time! You can also leave your contact information directly on the website, and we will contact you in time!