Let you understand the reasons for the cracks in the standard hook group
Manufacturers often receive customer reactions that when checking the hook group, they found cracks in the standard hook group and wanted to know the specific reason. Let the manufacturer take you to learn more about it.
1. Deformation temperature
The deformation temperature of the standard hook group has an important impact on the plasticity of the material. The temperature is low, the cold deformation and hardening are severe, and the plasticity is reduced; the temperature is too high, and it is easy to overheat and burn. Add a new sliding surface when the temperature exceeds 200 degrees Celsius. Therefore, during the deformation process, it should be ensured that deformation should be avoided as much as possible in the single-phase state.
2. Deformation speed
Deformation speed has a great impact on the plasticity of the material, and a suitable forged hook group should be selected according to the specific material.
3. Hot press deformation
Because recrystallization can be carried out smoothly during the thermal deformation process, the defects caused by deformation are partially reduced, thereby improving plasticity. Therefore, when purchasing, you should pay attention to the impact of this link on the hook group.
4. The tissue of the blast material
In order to improve the plasticity of the material, attention should be paid to reducing the low-melting point substances and brittle compounds in the standard hook group.
The above points are methods to avoid standard hook set cracks, and I hope they can help you.
Manufacturers often receive customer reactions that when checking the hook group, they found cracks in the standard hook group and wanted to know the specific reason. Let the manufacturer take you to learn more about it.
1. Deformation temperature
The deformation temperature of the standard hook group has an important impact on the plasticity of the material. The temperature is low, the cold deformation and hardening are severe, and the plasticity is reduced; the temperature is too high, and it is easy to overheat and burn. Add a new sliding surface when the temperature exceeds 200 degrees Celsius. Therefore, during the deformation process, it should be ensured that deformation should be avoided as much as possible in the single-phase state.
2. Deformation speed
Deformation speed has a great impact on the plasticity of the material, and a suitable forged hook group should be selected according to the specific material.
3. Hot press deformation
Because recrystallization can be carried out smoothly during the thermal deformation process, the defects caused by deformation are partially reduced, thereby improving plasticity. Therefore, when purchasing, you should pay attention to the impact of this link on the hook group.
4. The tissue of the blast material
In order to improve the plasticity of the material, attention should be paid to reducing the low-melting point substances and brittle compounds in the standard hook group.
The above points are methods to avoid standard hook set cracks, and I hope they can help you.
Manufacturers often receive customer reactions that when checking the hook group, they found cracks in the standard hook group and wanted to know the specific reason. Let the manufacturer take you to learn more about it.
1. Deformation temperature
The deformation temperature of the standard hook group has an important impact on the plasticity of the material. The temperature is low, the cold deformation and hardening are severe, and the plasticity is reduced; the temperature is too high, and it is easy to overheat and burn. Add a new sliding surface when the temperature exceeds 200 degrees Celsius. Therefore, during the deformation process, it should be ensured that deformation should be avoided as much as possible in the single-phase state.
2. Deformation speed
Deformation speed has a great impact on the plasticity of the material, and a suitable forged hook group should be selected according to the specific material.
3. Hot press deformation
Because recrystallization can be carried out smoothly during the thermal deformation process, the defects caused by deformation are partially reduced, thereby improving plasticity. Therefore, when purchasing, you should pay attention to the impact of this link on the hook group.
4. The tissue of the blast material
In order to improve the plasticity of the material, attention should be paid to reducing the low-melting point substances and brittle compounds in the standard hook group.
The above points are methods to avoid standard hook set cracks, and I hope they can help you.
Inquiry
Please leave us your requirements, we will contact you soon.