News

　　Everyone is familiar with hook, so who knows what the hook group is? In fact, the hook group is composed of multiple hooks. Of course, the hook group is also a major accessory used in lifting equipment.

　　Then the hook group will also be damaged. What is the main reason for its damage? Below, Weihua Lifting Equipment Factory will give us a detailed introduction.

　　The rotary hook group is made of alloy steel die forged.

　　Choose extra heat treatment skills to achieve the required high intensity.

　　Supply various rigging endings and connection parts: high-strength shackles, hooks, rings, orchid screws, etc., so that they can be used to connect with wire ropes, chains, hoisting belts, etc., and can be freely combined into various sets of rigging to meet the lifting needs of different occasions.

　　So what are the main uses of rotary hook sets? In fact, the hook group is mainly used for lifting machinery and equipment in infrastructure projects such as construction, highways, bridges, metallurgy, mining, electricity, slope tunnels, and shaft protection.

　　What is the damage method that can be seen from the appearance during the use of the rotary hook set? Wear at the hook and the pulley margins will often break.

　　So what is the reason for the pulley to break? The reason for the breaking of the pulley is mainly caused by bumps, that is, the hook group has not risen to the necessary height, the unstable driving of the car may be caused by the crooked pulling and swaying, and the heavy objects sway violently, causing the pulley group to touch other objects. Another situation is that the crane driver does not operate according to the construction rules and does not check the lifting status of the limit switch, but forms a hook to the sky, causing damage to the end of the pulley.

　　Of course, wear at the hook part is a normal appearance. The primary reason for this appearance is that when the heavy object is lifted, the center of gravity must be adjusted by itself, and then force the wire rope or hook to slide and wear at the hook mouth.

　　I wonder if you have a certain understanding of the reasons for the damage of the rotary hook group after reading the above introduction from Yiweihua Lifting Equipment Factory? Therefore, everyone must try to avoid it when using it.

　　Everyone is familiar with hook, so who knows what the hook group is? In fact, the hook group is composed of multiple hooks. Of course, the hook group is also a major accessory used in lifting equipment.

　　Then the hook group will also be damaged. What is the main reason for its damage? Below, Weihua Lifting Equipment Factory will give us a detailed introduction.

　　The rotary hook group is made of alloy steel die forged.

　　Choose extra heat treatment skills to achieve the required high intensity.

　　Supply various rigging endings and connection parts: high-strength shackles, hooks, rings, orchid screws, etc., so that they can be used to connect with wire ropes, chains, hoisting belts, etc., and can be freely combined into various sets of rigging to meet the lifting needs of different occasions.

　　So what are the main uses of rotary hook sets? In fact, the hook group is mainly used for lifting machinery and equipment in infrastructure projects such as construction, highways, bridges, metallurgy, mining, electricity, slope tunnels, and shaft protection.

　　What is the damage method that can be seen from the appearance during the use of the rotary hook set? Wear at the hook and the pulley margins will often break.

　　So what is the reason for the pulley to break? The reason for the breaking of the pulley is mainly caused by bumps, that is, the hook group has not risen to the necessary height, the unstable driving of the car may be caused by the crooked pulling and swaying, and the heavy objects sway violently, causing the pulley group to touch other objects. Another situation is that the crane driver does not operate according to the construction rules and does not check the lifting status of the limit switch, but forms a hook to the sky, causing damage to the end of the pulley.

　　Of course, wear at the hook part is a normal appearance. The primary reason for this appearance is that when the heavy object is lifted, the center of gravity must be adjusted by itself, and then force the wire rope or hook to slide and wear at the hook mouth.

　　I wonder if you have a certain understanding of the reasons for the damage of the rotary hook group after reading the above introduction from Yiweihua Lifting Equipment Factory? Therefore, everyone must try to avoid it when using it.