What malfunctions might occur during the use of a semi-enclosed hook assembly? How can they be inspe
Semi-closed hook group is a commonly used hook group accessories. This equipment can cooperate with lifting equipment for lifting operations, and is widely used in large-scale processing sites such as metallurgy and mining. Because its own use structure is relatively complex, once a failure occurs, it will directly affect the safety production at the construction site. Therefore, we need to understand the possible faults and inspection directions of the semi-enclosed hook group:
1. The hook has inflexible rotation
The reason for this situation is whether the gap in the rotational part is too small, and whether the hook cannot deflect normally due to problems such as the non-parallel holes of the beam shafts and pulley shafts of the two side plates.
2. The hook cannot rotate continuously
This situation is mostly caused by the vertical deflection angle not being paid attention to the gap of the beam during the installation of the hook structure.
3. The hook cannot lift normally and other work
This kind of feelingIn the case, it is necessary to check whether it is caused by bearing damage or wire rope stagnation. If not, it may be due to the increased rotational friction resistance, which causes the bearing to fail.
To sum up, it is an analysis of the possible causes of failures in the semi-enclosed hook group. Therefore, here the editor also calls on everyone to do a good job in daily lubrication of lifting accessories such as hooks to prevent the frequent occurrence of the above-mentioned faults and reduce production efficiency.
Semi-closed hook group is a commonly used hook group accessories. This equipment can cooperate with lifting equipment for lifting operations, and is widely used in large-scale processing sites such as metallurgy and mining. Because its own use structure is relatively complex, once a failure occurs, it will directly affect the safety production at the construction site. Therefore, we need to understand the possible faults and inspection directions of the semi-enclosed hook group:
1. The hook has inflexible rotation
The reason for this situation is whether the gap in the rotational part is too small, and whether the hook cannot deflect normally due to problems such as the non-parallel holes of the beam shafts and pulley shafts of the two side plates.
2. The hook cannot rotate continuously
This situation is mostly caused by the vertical deflection angle not being paid attention to the gap of the beam during the installation of the hook structure.
3. The hook cannot lift normally and other work
This kind of feelingIn the case, it is necessary to check whether it is caused by bearing damage or wire rope stagnation. If not, it may be due to the increased rotational friction resistance, which causes the bearing to fail.
To sum up, it is an analysis of the possible causes of failures in the semi-enclosed hook group. Therefore, here the editor also calls on everyone to do a good job in daily lubrication of lifting accessories such as hooks to prevent the frequent occurrence of the above-mentioned faults and reduce production efficiency.
Semi-closed hook group is a commonly used hook group accessories. This equipment can cooperate with lifting equipment for lifting operations, and is widely used in large-scale processing sites such as metallurgy and mining. Because its own use structure is relatively complex, once a failure occurs, it will directly affect the safety production at the construction site. Therefore, we need to understand the possible faults and inspection directions of the semi-enclosed hook group:
1. The hook has inflexible rotation
The reason for this situation is whether the gap in the rotational part is too small, and whether the hook cannot deflect normally due to problems such as the non-parallel holes of the beam shafts and pulley shafts of the two side plates.
2. The hook cannot rotate continuously
This situation is mostly caused by the vertical deflection angle not being paid attention to the gap of the beam during the installation of the hook structure.
3. The hook cannot lift normally and other work
This kind of feelingIn the case, it is necessary to check whether it is caused by bearing damage or wire rope stagnation. If not, it may be due to the increased rotational friction resistance, which causes the bearing to fail.
To sum up, it is an analysis of the possible causes of failures in the semi-enclosed hook group. Therefore, here the editor also calls on everyone to do a good job in daily lubrication of lifting accessories such as hooks to prevent the frequent occurrence of the above-mentioned faults and reduce production efficiency.
Inquiry
Please leave us your requirements, we will contact you soon.